Application:

Use directly from container. It is not necessary to mix or add water. Material is best applied using a hawk and standard size 3"x 10" stainless steel finishing trowel. Master of Plaster basecoat is self leveling. Apply basecoat to all surfaces as thinly as possible. As material starts to set (approx. 15-20 minutes) go back over work and trowel as smooth as possible, (some ridges and trowel marks will remain) . Allow to set 3-4 hours, overnight is recommended.

When basecoat has dried, apply second coat of basecoat as thinly and smoothly as possible. As material starts to set ( approx. 10-15 minutes) using a small plant mister
(spray bottle) lightly spray area with water and smooth removing all trowel marks and blemishes. Since "Master of Plaster" feathers out and blends easily, it is possible to work smaller areas rather than having to do one large area at a time. Just keep the edges wet and it will all blend together. "Master of Plaster" is a very forgiving system. If an area gets too dry, or you did not get all the trowel marks out, just re-wet and trowel until the desired effect is achieved.

Two coats of "Master of Plaster" basecoat will produce a smooth dead flat finish with a slight tooth. This is a finish suitable for many older residential structures where oftentimes the finish coat was left off allowing for better suction for paint or was left to be papered.

If a smoother more polished finish is desired,apply a coat of "Master of Plaster" finishcoat.
After the second basecoat has dried apply the finish as thinly as possible. Again working in smaller areas (4 or 5 square feet) keep working the finish removing all trowel marks and blemishes, and move on to the next area. As one area starts to dry, lightly spray with a plant mister and re-trowel. As you re-trowel the finish will become smoother and shinier. It is possible to go from a low luster to a mirror finish by just troweling. The more you work it with a trowel the shinier it will get.

Coverage:

Basecoat 170-220 square feet per 5 gallon bucket.
Finishcoat 510-600 square feet per 5 gallon bucket.
Master of plaster is meant to be applied as thinly as possible. Two coats of basecoat and one coat of finish should not be much thicker than a coat of paint. If applied as thinly as possible the higher coveage will be achieved. Since "Master of Plaster" goes on so thin there is no need to worry about loosing detail on cornices and casework.

Drying Time:

For best results, four to six hours drying time at temperatures above 50 degrees is recommended between coats.

Textures and Finishes:

Master of Plaster was specifically designed to produce a smooth, hard, polished surface. Variations in finishes and textures are, however only as limited as your imagination.

In addition to the more traditional spatterdash, and travertine finishes, is also possible to do sgraffito, impressed plaster, and colored plaster, as well as glazes and washes. Virtually any finish done with traditional plaster can be achieved using "Master of Plaster".

Painting and Decorating:

It is recommended that "Master of Plaster" finishes be allowed to cure for 1-2 weeks before painting. After curing, any good quality paint may be used in accordance with paint manufacturers instructions.

Cleanup:

Wash tools with plain water. Wipe dry to prevent rusting.

Storage:

Keep containers tightly closed. After material has been removed, replace cover. To preserve remaining material at the end of a project. Scrape sides of bucket and cover with cellophane or 1 inch of water. Unused material will keep for up to a year following these practices.

Shelf life of unopened material is 2 years. Do not store outside. Keep out of direct sunlight. Protect from freezing.

Caution:

Master of Plaster was designed not to be sanded. This product contains mica . Long term breathing of large amounts of mica dust may cause lung disease. Do not sand. Use of safety glasses is recommended.
Keep out of the reach of children.

Liability:

We shall not be liable for incidental and consequential damages, directly or indirectly sustained, nor for any loss caused by application of these goods not in accordance with current printed instructions or for other than intended use. Our liability is expressly limited to replacement of defective goods.